Teflone Products

Teflone-Rods-and-Sheets

Properties:

PTFE molded sheet molding process by suspension PTFE resin with good corrosion resistance, aging resistance, low coefficient of friction,
Using a big range.

Main purpose:

Machinable making gaskets, seals, lining shelves, scraper, guide, and a variety of frequencies used in electrical insulation parts, bridge bearing slide.
Service Life
PTFE exhibits excellent retention of properties after a long period of time, even at elevated temperatures and in the presence of oils, solvents, UV light, oxidizing agents and other environmental agents.

1) 100% Virgin PTFE
2) Tensile strength: >15Mpa
3) Elongation at break: >200%
4) Density: 2.1-2.3g/cm3
5) Break down voltage: 10KV/mm
6) Temp resist: -180℃ ~ +260℃
7) For mold pressed sheet
a) Size: 1000 x 1000mm,1200 x 1200mm,thickness: 2 – 70mm
b) Size: 1500 x 1500mm,thickness: 4 – 70mm
c) Size: Maximum 1800mm x 1800mm
8) For skived sheet
a) Width:1000 – 2000mm (special sizes could be ordered)
b) Length no limited, thickness: 0.2 – 6mm

Regular Sizes:

Thickness mm,

Tolerance

150×150

1.0100

±0.30±0.50

250×250

1.5100

±0.30±0.50

300×300

1.5100

±0.30±0.50

450×450

1.5100

±0.30±0.50

600×600

2100

±0.30±0.50

800×800

2100

±0.30±0.50

1000×1000

3100

±0.30±0.50

1200×1200

3100

±0.30±0.50

1600×1600

540

±0.40±0.80

1000×2000

540

±0.40±0.80

1800×1800

540

±0.40±0.80

Teflon PTFE

(Poly Tetra Fluoro Ethylene) Rod,
1. Extruded Rod, Moulded Rod-180°C – +260°C with Best Electrical Properties
2. Any sizes according to customer’s demand
3. Carbon, graphite can be filled

PTFE Rod is manufactured in two distinct ways, extruded PTFE Rod is the most popular and is relevant to smaller sizes, Moulded PTFE Rod is relevant to the diameters over 100mm in size, smaller sizes are also available in extruded form. Molded Teflon rod has a wide range of practicable temperature from -180°C – +240°C and a wax-like surface to which anything hardly rods. Molded PTFE rod has the lowest coefficient of friction of all known solid materials. It has the best electrical properties of all plastics.

Regular Sizes:

Diameter: 3, mm to 300, mm
Length: 300 mm and 1000 mm
we can provide customized (special) sizes on request

PTFE Bush

Regular Sizes::
Outer Diameter O.D.: 12.5 mm to 250 mm;
Inner Diameter I.D.: 12.5 mm to 250 mm;
Length: 100 mm to 300 mm
We can provide customized (special) sizes on request;

Flexible PTFE Tubing

Regular Sizes:
Outer Diameter O.D.: 3.2 mm to 28.0 mm;
Inner Diameter I.D.: 1.6 mm to 25.1 mm;
Wall thickness: 0.8 mm to 1.6 mm
Length: 3 meters to 120 meters
We can provide customized (special) sizes on request;

PTFE Pipes (Rigid)

Regular Sizes:
Outer Diameter O.D.: 25 mm to 100 mm;
Inner Diameter O.D.: 19 mm to 89 mm;
Wall thickness: 3 mm to 25 mm
Length: up to 50 meters

Note: We can provide customized (special) sizes on request,
Fillers such as Glass/ Carbon/ Graphite/ Bronze + MOS2; are available for PTFE Rods and Bushes


PTFE Tape (Thread Sealant)

PTFE in tape form is the standard material for sealing threaded joints and connections. Joints can be taken apart long afterward without any trouble. It is virtually a universal sealing material which can be used on pipes of galvanized Iron, Rubber, Copper, Plastic Brass, Aluminium, Stainless Steel, Ceramic, Monel, Carbon etc.
The inherent plasticity of PTFE allows it to extrude into the irregularities of the thread, so filling any voids or passages. It is inert to acids, solvents oil, etc. and will not contaminate the liquid being handled.
Regular Sizes:
Width: 12.5 mm to 25 mm (1/2” to 1”)
Length: 12 meters
Thickness: 0.075 mm

PTFE Cut Gaskets;

Solid flat PTFE gaskets, PTFE O ring gaskets are used against strong acids, alkalis and organic solvents up to 110oC and pressure up to 20Kg/Cm2.

PTFE Solid Ring Gasket

Regular Sizes: as per ASA 150 #
Size: 15 mm NB to 300 mm NB
Thickness: 1.5 mm, 2 mm, 3mm